Binder effect on cycling performance of silicon/carbon composite anodes for lithium ion batteries

The cycling performance of a silicon/carbon composite anode has been significantly enhanced by using acrylic adhesive and modified acrylic adhesive as binder to fabricate the electrodes for lithium ion batteries. The capacity retentions of Si/C composite electrodes bound by acrylic adhesive and modified acrylic adhesive are 79% and 90% after 50 cycles, respectively. These two binders are electrochemically stable in the organic electrolyte in the working window. They also show larger adhesion strength between the coating and the Cu current collector as well as smaller solvent absorption in the electrolyte solvent than polyvinylidene fluoride (PVDF). Furthermore, sodium carboxyl methyl cellulose (CMC) plays an important role on improving the properties of acrylic adhesive, which increases the adhesive strength of acrylic adhesive and improves the activation of the electrodes.     

Advanced Sn/C composite anodes for lithium ion batteries

Metallic tin was deposited in fine particulate form on the surface of carbonaceous mesophase spherules (CMS) and in the pores of porous carbon by the decomposition and reduction of tin(II) 2-ethylhexanoate at 450 °C. The Sn/C composite powders obtained were used as anode materials for lithium ion cells. Electrochemical cycling tests of coin cells show that the dispersion of tin into the carbonaceous materials enhances the reversible capacity of the electrodes. The capacity retention at the 50th cycle is 91 % for Sn/CMS composite containing 22% tin, against 428 mAh g^–1 at the first cycle. With further increase in tin content, the capacity fade upon cycling is more rapid.     

锂离子电池层状LiMnO2正极材料的研究进展

论述了锂离子电池层状LiMnO2正极材料的结构、性能、制备、存在的问题和掺杂改性等方面的研究状况,讨论了今后层状LiMnO2的研究趋势.     

羧甲基纤维素包覆天然石墨性能的研究

本实验研究了羧甲基纤维素(CMC)包覆对天然石墨电化学性能的影响。通过XRD、恒电流充放电测试手段研究了不同包覆量对该复合材料结构和电化学性能的影响。结果表明:羧甲基纤维素裂解炭对天然石墨有较好的包覆作用,并且能够有效的阻止石墨在充放电过程中发生层状剥落现象,从而有效的提高复合炭材料的循环稳定性,其中5%树脂包覆量的复合材料在循环50次之后可逆容量是310.9 mAh.g-1,比天然石墨高50 mAh.g-1,并保持了首次可逆容量的97.1%。     

NiFe2O4隋性阳极的制备及其电解腐蚀机理

以Fe2O3和NiO为主要原料，添加2％（按质量计）MnO2，采用固相烧结工艺制备了NiFe2O4惰性阳极。用X射线衍射和扫描电子显微镜对材料的组成和微观结构进行了研究，测量了样品在冰晶石熔盐中不同电流密度下的电解腐蚀速率，并对其腐蚀机理作了初步探讨。结果表明：惰性阳极由NiO和NiFe2O4尖晶石两相组成，MnO2作为固溶体在尖晶石晶界处富集。电解腐蚀呈现出物理化学溶解过程，熔盐对试样的电解腐蚀首先要在晶界处发生反应生成更稳定的FeAl2O4相，而FeAl2O4相结构致密，冰晶石熔盐通过该相向NiFe2O4尖晶石晶粒内扩散速度减慢，从而降低了腐蚀速率。     

镁铝合金阳极氧化表面处理工艺研究

研究了镁铝合金的阳极氧化过程,通过表面处理、化学清洗(脱脂除油)、碱蚀、化学抛光、电解着色、水合封孔、清洗和干燥等过程,得到符合国家标准的镁铝合金成品。     

浅析预焙阳极配料控制

分析了粉料纯度及配料控制对炭阳极生产和炭阳极成品率的影响，结合中国铝业青海分公司的生产状况，从预焙阳极配料控制方面，就如何提高炭阳极成品率、保持生阳极生产工艺稳定进行论述。     

影响酸性电镀铜用磷铜阳极质量因素的探讨

主要探讨了影响电镀铜用磷铜阳极质量的因素,包括原材料、铜晶粒结构、磷含量及阳极表面的清洁。分别比较了某公司磷铜阳极标准与国内一般磷铜阳极标准、粗大铜晶粒结构与精细铜晶粒结构图,并将该公司揉制磷铜球黑膜形成及表面溶解状况与低质量轧制磷铜球进行了比较。介绍了优质铜阳极的特点:低金属杂质;铜晶粒精细、规整;磷铜阳极的磷含量为0．04％-0．065％且均匀分布等。     

Electrochemical ferrate generation for waste water treatment using cast irons with high silicon contents

This paper deals with the electrochemical preparation of ferrate in 15 M NaOH media, with a view to treatment of waste waters. Grey cast irons with high silicon contents were shown to allow current yields in the range 20–40% depending on the applied current density, up to 34 mA cm^–2. Ferrate solutions with contents up to 0.08 M could be produced in a divided cell of simple design, and provided with flat or packed-bed electrodes. Deactivation of the anode surface was shown to be of moderate significance for hour-long runs. The ferrate produced was tested for treatment of industrial liquid wastes: coagulation efficiency of the suspended matter was comparable with that of an electrocoagulation process with sacrificial Al anodes. The potential of waste water treatment by addition of ferrate is discussed.     

延长预焙阳极使用周期的研究与应用

通过分析延长预焙阳极使用周期的途径、阳极消耗的影响因素以及预焙阳极生产工艺状况，确定通过提高预焙阳极的质量来延长其使用周期，研究制定并详细论述了改善预焙阳极质量的具体工艺改进措施。阐述了改进预焙阳极工艺后取得的效果、预焙阳极的质量状况以及为企业创造的经济效益和社会效益。